You may also like…

• 

  24″ EarthX Quick Connect Cables

  $22.99

  24″ Long Quick Connect Charging/Jump Start Cables

  You can permanently install this quick connect cable to your battery (lead acid or lithium) that can be used for quick, easy access for charging or be used with a portable jump starter to jump start your battery in seconds! No removal of seats, no removal of battery covers, no tools needed, no time wasted! Engineered and designed to carry 400 amps of energy without melting the wire by using 150 strand insulated copper wire. The standard SAE fitting will fit any standard portable jump pack on the market today.

  

  Add to cart
• 

  EarthX Portable Lithium Iron Phosphate (LiFePo4) Jump Pack

  $129.00

  One of the most amazing gadgets out there! No need to ask anyone for assistance and you can jump your own vehicle in seconds!

  The EarthX Jump Pack is light and compact so you can take it anywhere to start just about anything with 400 burst cranking amps (cars, up to a V8 trucks, boats, motorcycles, ATV/UTV’s , airplane’s and snowmobile’s, riding lawnmower’s, etc.).  The entire kit only weighs 1.4 pounds and comes with the jump pack unit, the plug in the wall charger, alligator jumper cables, and the case! The EarthX Jump Pack is custom designed for rugged off road use featuring dust covers for all power and charge ports, plus an “easy hold” grip with a rubber like finish.

  And like our EarthX batteries, the EarthX Jump Pack uses lithium iron phosphate (LiFePo4) cells, not Lithium Cobalt (LiCoO2)!  This is a big deal! LiFePo4 is the most stable and robust of all the lithium chemistries, has  double the life span compared to lithium cobalt and is the correct voltage range as your vehicle you are jumping!

  The EarthX Jump Pack uses 4 Lithium Iron Phosphate (LiFePo4) cells in series at a voltage range 10V-14.6V vs. a Lithium Cobalt (LiCoO₂) jump pack that uses 3 cells at a voltage range of 9V-12.6V.

  Why is this a very important difference? This means the voltage of the EarthX Jump Pack  is 100% compatible with your vehicles charging system and at no risk of over charging as the normal charge range is up to 14.6V, which is what your vehicles will produce once started. The jump pack that uses the Lithium Cobalt cells must use diodes in the jumper cables to protect the cells from the excess voltage and why they say to immediately remove the jump pack after start. If this diode fails, the Lithium Cobalt cells can and will be overcharged causing damage to the cells and even cell rupture/fire.

  Here at EarthX, performance and safety is paramount and it would be much cheaper to use the inferior cells but we want you to have only the best!  If the jump pack you are researching doesn’t tell you it’s a LiFePo4 technology, it not! Go to this link to see a video on how to jump start a vehicle: http://www.youtube.com/watch?v=PW3hcgsGsok

  Other features include:

  • USB 5V/2.1A port to charge/power electronic devices (charges cell phone, I-pad)
  • 12V output
  • High intensity LED flashlight
  • Charge level indicator LEDs
  • Once charged, will hold it charge level for up to a year!
  • Reverse connection protection
  • Built in electronics to protect the battery from over-discharge/over-charge
  • Water-resistant carrying case
  • Unique rubber coating on the outside for ease of holding even in bad weather!
  • Designed for rugged conditions with plastic covers for all the ports to keep dust and water out!
  • Has a 1 year warranty. If you purchase direct, we will have you in our system, otherwise, save your receipt.

  View/Download Jump Pack Manual (PDF)

  Add to cart
• 

  OptiMate 5 amp Lithium Battery Charger Model TM-291with BMS reset

  $129.90

  To reset an EarthX battery that is in the over discharge protection mode, connect alligator clips FIRST, and then plug unit into the wall. You will see the lights go to the save mode.

  Add to cart
• 

  OptiMate 9.5 amp Lithium Battery Charger Model TM-271with BMS reset

  $179.90

  To reset an EarthX battery that is in the over discharge protection mode, connect alligator clips FIRST, and then plug unit into the wall. You will see the lights go to the save mode.

  Add to cart